供应生产中的劲拓十温区氮气回流焊，另有劲拓8温区回流焊出售。
我司长期专业供应SMT二手贴片机，回流焊，波峰焊，印刷机，及SMT周边设备，提供一站式SMT贴装解决方案。
| 回流焊参数 | |
| 型号 MODEL | VS-1000II / NS-1000II |
| 机体参数 GENERAL | |
| 外型尺寸(L*W*H) Outside Dimension(L*W*H) | 6100x1353x1490mm |
| 颜色 Standard Color | 计算机灰 Computer Grey |
| 重量 Weight | Approx.2450KG |
| 加热区数量 Number Of Heating Zones | 上Up10/下Bottom10 |
| 加热区长度 Length Of Heating Zones | 3891mm |
| 冷却区数量 Number Of Cooling Zones | 2(内置) |
| 排风量要求 Exhaust Volume | 10 M3/ min x 2 (通道) Exhausts |
| 控制部分参数 Standard Feature Of Control System | |
| 电气要求 Electric Supply Required | 3 phase,380V 50/60Hz(optional: 3 phase,220V 50/60Hz 选配) |
| 电源功率要求 Electric Power Required | 80KW |
| 启动功率 Power For Warm Up | 36KW |
| 正常功率消耗 Power Consumption | 13KW |
| 升温时间 Warming Time | 约 Approx.25 minute |
| 温度控制范围 Temp. Setting Range | 室温 Room Temp. --- 300℃ |
| 温度控制方式 Temperature Control Method | PID闭环控制 + SSR驱动 / PID Close Loop Control + SSR Driving |
| 温度控制精度 Temperature Control Precision | ± 1.0℃ |
| PCB板温分布偏差 Temperature Deviation on PCB | ± 1.5℃ (by JT Board Test Standard) |
| 加热器 Heating Element | Especial Heating elements For Long Life ;特制的特长寿命加热器 |
| Commutated Element 整流板结构 | Aluminium Alloy Plate铝板 |
| Max. Temp. Gap Between Preheat & Reflow Setting 预热区和焊接区之间的最大温度设定差值 |
80℃ |
| Max. Temp. Gap Between Preheat Zones Setting 预热区之间的最大温度设定差值 |
40℃ |
| Max. Temp. Gap Between Reflow Zones Setting 焊接区之间的最大温度设定差值 |
50℃ |
| 参数存储 Data Storage | 可存多种生产设置参数与状况 Process Data and Status Storage (80GB) |
| 异常报警 Abnormal Alarm | 温度异常（恒温后超高温或超低温）Abnormal Temperature (Extra-high / Extra-low Temp.) |
| 掉板报警 Board Dropped Alarm | 三色信号灯: 黄-升温；绿-恒温；红-异常 Tower Light: Yellow–Warming; Green-Normal; Red-Abnormal |
| 运输参数 Standard Features Of Conveyor System | |
| 导轨数量 | 1 Lane |
| Rail Structure 导轨结构 | Subsection Integrated Type整体分段式Subsection Separate Control分段独立控制(Option选配) |
| PCB最大宽度 Max.Width Of PCB | 400mm (Option:610mm 选项) |
| 导轨调宽范围/调宽形式 | 50--400mm(Option:50--610mm 选项)/电动 Motorized |
| Range Of Rail Width/Adjustment | |
| 部品高度 Components Clearance | PCB板上/下各25mm , Top/ Bottom Clearance of PCB is 25mm |
| 运输方向 Converyor Direction | 左向右(选配: 右向左) L→R (Option: R→L) |
| 运输导轨固定方式 Fixed Rail Side | 前端固定(选配:后端固定)Front Rail Fixed(Option:Rear Rail Fixed) |
| PCB运输方式 PCB Transmission Agent | 空气炉 Air-Reflow = 链条+网带 Chain + Mesh ,氮气炉 N2-Reflow空气炉 Air-Reflow = 链条+网带 Chain + Mesh , 氮气炉 N2-Reflow = 链条 Chain (可选配网带 Mesh is option) |
| 中央支撑 Center Support (选配 Option) | 防止PCB板因过宽及元器件过重而弯曲变形 Preventing PCB warp such too wide and heavy component load |
| 运输带高度 Converyor Height | 900±20mm |
| 运输速度 Converyor Speed Range | 300～2000mm/min |